865 Highway 169 N.
Plymouth, Mn. 55441
DVD INSTRUCTIONAL VIDEO - "SKATE
SHARPENING THE WISSOTA WAY". STANDARD EQUIPMENT WITH EVERY MACHINE.
THEORY, PRINCIPALS, SET-UP, OPERATION, AND MAINTENANCE OF WISSOTA SKATE
SHARPENING MACHINES. DVD IS 60 MINUTES LONG. $9.00 IF ORDERED
SEPARATELY, INCLUDES POSTAGE TO CONTINENTAL USA. (NOTE: EACH
MACHINE COMES WITH ONE DVD INSTRUCTIONAL VIDEO).
VHS INSTRUCTIONAL VIDEO TAPE - "SKATE
SHARPENING THE WISSOTA WAY". THEORY, PRINCIPALS, SET-UP, OPERATION AND
MAINTENANCE OF WISSOTA SKATE SHARPENING MACHINES. VHS IS 60 MINUTES LONG.
$13.85 - INCLUDES POSTAGE TO CONTINENTAL USA. (NOTE:
EACH MACHINE COMES WITH ONE DVD INSTRUCTIONAL VIDEO).
GRINDING WHEELS
WARNING! SKATE SHARPENING CREATES DUSTS. EXCESSIVE DUST INHALATION WILL ADVERSELY AFFECT YOUR RESPIRATORY HEALTH. ALWAYS CONSIDER THE MATERIAL BEING GROUND WHEN SELECTING DUST CONTROL MEASURES. WISSOTA CAN NOT CONTROL THE CHEMICAL PROPERTIES OF THE STEEL YOU WILL GRIND. THEREFORE ALWAYS WEAR AN APPROPRIATE TIGHT FITTING DUST MASK WHEN OPERATING THE MACHINE.
WARNING! ALWAYS WEAR EYE PROTECTION
WHEN OPERATING THE MACHINE.
7x3/8x1/2 GRINDING WHEEL. 60 GRIT, BROWN ALUMINUM OXIDE, MEDIUM HARD. GENERAL PURPOSE. A FAVORITE FOR MANY YEARS. EXCELLENT COMBINATION OF GRINDING, FORM HOLDING, FINISH, AND WHEEL LIFE. FOR MODEL 911 MACHINES. $24.00
7x3/8x1/2 GRINDING WHEEL. 80 GRIT, PINK ALUMINUM OXIDE, MEDIUM SOFT. STANDARD EQUIPMENT ON ALL NEW MACHINES. THE PINK MATERIAL PERFORMS BETTER ON BLADES WITH HIGH STAINLESS STEEL CONTENT. FOR MODEL 911 MACHINES. $24.00
NOTE : ALL WHEELS ABOVE ARE BORED TO SIZE. THERE ARE NO BUSHINGS USED. EACH WHEEL IS SIDE FINISHED TO REMOVE ANY WOBBLE. EACH OUTSIDE DIAMETER IS DRESSED AGAINST THE INSIDE DIAMETER TO REMOVE HOP. EVERY WHEEL IS HAND BALANCED. YOU CAN FIND WHEELS WITH DIFFERENT GRINDING PROPERTIES THAN OURS, BUT YOU WILL NOT FIND A BETTER RUNNING WHEEL.
DIAMOND DRESSER TOOLS
1/2" O.D. x6" LONG 1/4 K DIAMOND. SPECIALLY SELECTED AND SET FOR THIS APPLICATION. INCLUDES RADIUS RULER MARKINGS. FOR MODEL 911 OR S8B $26.00
5/16-22 (THREADED) x3" LONG. 1/4 K DIAMOND FOR S8 MACHINE.$26.00
 |
ONE FULL TURN OF THE TILT CONTROL KNOB WILL CHANGE THE DISPARITY OF THE BLADE EDGES BY APPROXIMATELY 0.001" (HOCKEY) AND 0.0014" (FIGURE). |
WISSOTA "TANGENT FINDER" SKATE HOLDER , HOLDS HOCKEY, GOALIE, AND FIGURE SKATES. ADJUSTABLE FOR OVERALL HEIGHT, INDEPENDENT SIDE TO SIDE (DEGREE OF LEVEL), AND IN OR OUT TILT (ANGLE OF APPROACH). CAST ALUMINUM WITH REPLACEABLE WEAR PADS. QUICK RELEASE JAWS ARE STEEL INVESTMENT CASTINGS. HAND KNOBS FOR SMOOTH CONTROL. STANDARD 45/8" HEIGHT FOR ALL WISSOTA MACHINES. CAN BE ORDERED AS 41/2" FOR OTHER POPULAR MACHINES. $210.00
NEW! IMPROVED TILT CONTROL KNOB.THIS KNOB IS
NOW STANDARD EQUIPMENT ON ALL NEW TANGENT FINDER HOLDERS. THIS ALUMINUM KNOB
HAS THE INSTRUCTIONS STAMPED ONTO THE FACE SO THAT THE OPERATOR CAN EASILY SEE
WHAT TO DO. IT READS. "TO CORRECT HIGH TOP EDGE TURN ->, TO CORRECT
HIGH BOTTOM EDGE TURN <-, ONE FULL TURN EQUALS APPROXIMATELY 0.001"
EDGE CHANGE". UPDATE YOUR OLDER HOLDER FOR $9.00.
NEW, “ELITE” FIGURE SKATE HOLDER COMPLETE (OR JAW SET). DESIGNED SPECIFICALLY FOR AND WILL ONLY HOLD FIGURE SKATES. HOLDS ALL SIZES OF FIGURE SKATES, BABY THRU ADULT. LOCATES AND HOLDS ACROSS THE STANCHIONS SO THAT PARABOLIC, AND EVEN SIDE HONED, TAPERED BLADES ARE HELD ACCURATELY AND CONSISTENTLY.
NOTE: THE STANDARD TANGENT FINDER SKATE HOLDER THAT COMES WITH THE MACHINE WILL HOLD HOCKEY, GOALIE, AND FIGURE SKATES, BUT WILL NOT HOLD THE SPECIAL SIDE HONED FIGURE BLADES OR “BABY” SIZE SKATES.
CLICK HERE FOR MORE INFORMATION AND PRICING ON THE “ELITE” FIGURE SKATE HOLDER.
SKATE HOLDER
KNOBS. PROVIDE BETTER CONTROL. OLDER WISSOTA HOLDERS WILL REQUIRE
DRILLING/TAPPING TWO HOLES. $3.35 each (NOTE: THESE ARE INCLUDED ON ALL
NEW MACHINES).
SKATE HOLDER WEAR PADS. FELT, PRE-CUT, SELF STICK. $6.00 pair
LUBE WAX STICK. A LIGHT COAT ON THE SKATE BLADE BEFORE THE LAST PASS PROMOTES COOLER CUTTING AND BETTER FINISH. $6.00
ECCENTRIC PIN CONVERSION KIT. FOR PRE-SEPT-1994 SKATE HOLDER. ALLOWS INDEPENDENT TIP AND TAIL HEIGHT ADJUSTMENT TO CONTROL THE DEGREE OF LEVEL OF THE JAWS. $8.00 kit
WISSOTA BLADE STRAIGHTENER.
THE WISSOTA BLADE STRAIGHTENER HAS THE POWER AND THE DELICACY TO STRAIGHTEN ALL SKATE BLADES-HOCKEY, HOCKEY GOALIE, AND FIGURE. THE RAM IS CAPABLE OF APPROXIMATELY 1000# OF FORCE, YET CAN BE VERY DELICATELY CONTROLLED. THE BLADE SUPPORTS ARE MAGNETIC AND CAN BE POSITIONED ANYWHERE ALONG THE RUGGED BOTTOM TABLE. THE STRAIGHTENER IS ENTIRELY MADE OF CAST IRON AND STEEL FOR DURABILITY.
#WSBS ACTUAL WT 22 LBS SHIPPING WT 28 LBS $ 130
HAND HONES.
USE TO REMOVE FINE BURRS AND NICKS. ALUMINUM OXIDE. $2.75
ea. (TIP: TWO HAND HONES CAN BE RUBBED TOGETHER TO KEEP
THEM FLAT AND CLEAN).
DUST COLLECTOR HOOD. ALLOWS THE MACHINE TO BE EASILY HOOKED UP TO A VACUUM DUST CONTROL SYSTEM. 4" ROUND HOSE FLANGE. GALVANIZED STEEL. NEW MACHINES ARE PRE-DRILLED. OLDER MACHINES REQUIRE DRILLING TWO HOLES. $143.00
PD-9 PEDESTAL STAND. INDUSTRIAL DUTY, ALL STEEL, ALL WELDED. BOTTOM IS 5/16" THICK PLATE STEEL. 18" x 18". WEIGHT 54#. HEIGHT 33". $139.00
NEW TRAVEL CASE. WISSOTA'S NEW TRAVEL CASE IS 21 POUNDS LIGHTER THAN OUR OLD STEEL CASE! SECURELY HOLDS THE MACHINE, SKATE HOLDER, SPARE WHEEL, AND SPARE DIAMOND. "A PLACE FOR EVERYTHING AND EVERYTHING IN ITS PLACE". THE SHARPENER CAN BE OPERATED WHILE IN THE CASE. SPRING LOADED PADDED HANDLES, CAM ACTION LATCHES, AND ROLLER CASTORS TO EASE TRANSPORT. PERFECT FOR ALL TRAVEL OR TOURNAMENT GAMES. 28" X 22" X 13' HIGH, 21 LBS.$460.00
TRAVEL WEIGHT OF MACHINE IN CASE (AIRLINE WEIGHT) IS 85#.
PRICES DO NOT INCLUDE U.P.S. SHIPPING CHARGES
Return to Skate
Sharpener Index Page
Return to
Wissota Manufacturing HomePage
Order Form
1996 Wissota Manufacturing
Company
